|
Tomasz,
I see this intermittently as well. I run my
code (which is a for loop style) in the backtester. I have DebugView
running and _TRACE statements in several places throughout my for loop. I
do this to capture the bar time of my Buy, Sell, Short and Cover
statements. If you know what conditions might cause this, great.
Otherwise I just want to report it so that you know about it. I will try
and get better repro steps for you soon.
Even when it does not fail as below, I see far
fewer trades in the backtester grid than what is reported in DebugView.
It's almost like the loop is going too fast for the trades to get added to the
grid (which doesn't seem likely, but that is the behavior).
Thanks,
Brian
----- Original Message -----
Sent: Monday, May 30, 2005 7:52 AM
Subject: Re: [amibroker] Non-functioning
backtester
Hello,
AmiBroker does NOT use NotifyAlert.exe and
does NOT use
"common language runtime" (a .NET component).
The very
first thing I suggest is to perform thorough virus scan,
because the
message you get does not come from anything AmiBroker-related.
Best
regards,
Tomasz Janeczko
amibroker.com
----- Original Message -----
From: "David Nowotnik" <dnowotnik@xxxxxxxxx>
To:
<amibroker@xxxxxxxxxxxxxxx>
Sent: Monday, May 30, 2005 3:26
PM
Subject: [amibroker] Non-functioning backtester
> Can
anyone advise on the following problem? Backtest does not work;
>
instead, I get a one-line result with the 'value' -1.#J% in % change
>
(and similar -1.# values in some other fields).
>
> As more
background, I'm using version 4.70.5 of Amibroker, set up on
> a Dell
laptop and a Gateway PC. The problem occurs on the laptop but
> not on
the PC; in other words, several scripts that work without a
> problem
on the PC do not work on the laptop. In back test, most
> scripts that
I use on my laptop do not work, but the odd one or two
> still seem to
work OK (and all work on the PC).
>
> I believe that that the
problem may be related to a utilty that
> Amibroker uses, as I get an
error message on powering up my laptop,
> which says...
>
> ===========================
> NotifyAlert.exe - Common Language
runtime debugging services
> Application has generated an exception that
could not be handled
>
> Process id=0xff0 (4080), Thread id=0xff4
(4084).
>
> Click OK to terminate the application
> Click
CANCEL to debug the application
> ============================
>
> Click CANCEL, and this messages appears:
> Registered JIT
debugger is not available
>
>
============================
>
> As I primarily use Amibroker on
the laptop, I'd rather fix the
> problem than simply abandon the use of
Amibroker on that system!
>
> David
>
>
>
>
>
> Please note that this group is for discussion
between users only.
>
> To get support from AmiBroker please send
an e-mail directly to
> SUPPORT {at} amibroker.com
>
> For
other support material please check also:
> http://www.amibroker.com/support.html
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
Please note that this group is
for discussion between users only.
To get support from AmiBroker please
send an e-mail directly to
SUPPORT {at} amibroker.com
For other
support material please check also:
http://www.amibroker.com/support.html
Please note that this group is for discussion between users only.
To get support from AmiBroker please send an e-mail directly to
SUPPORT {at} amibroker.com
For other support material please check also:
http://www.amibroker.com/support.html
Yahoo! Groups Links
|